Have been lurking around and finally made my first purchase on the Redsuns + Drop Red Samurai TKL. The set is beautiful but there was 1 keycap that came disfigured/damaged. That kinda killed my excitement. Put in a ticket for support but have not heard back from them yet. Hope they make this right..
I was trying to flash my Drop Carina in an attempt to make it have the same lighting as this video: https://www.youtube.com/shorts/0iIzTWxev0g
However, when I tried to flash the board, I used the wrong file by mistake, and that file was for the Drop Shift. A singular orange LED lit up at the front of the board and it became unresponsive. When I plug it into my laptop, it makes a noise to show that the device recognises it, but it doesn't register me pressing the keys, and no lights turn on. Device manager shows three keyboards when my mouse is plugged in, but two when the mouse isn't plugged in (Excluding the laptop's keyboard). I have tried to flash the board again using the reset button on the back of the board, but I'm not sure it's working as there is a layer of foam in the way of the PCB and the case. Is there any way to do some sort of factory reset on this keyboard to reset the firmware?
Many thanks.
P.S I am in the UK
About six months ago, I got my first OTL DAC and it has been life changing. I have a hard time not using my DAC. I also got some ATH-R70x headphones to go with it. I've run into a problem, though. Lately, I've been getting some really serious feedback from my headphones. I'm a little worried, and want to get some insight into what on earth could be going on with my Audio setup. I'm fine with replacing some of the pieces, but I'd rather know what I need to replace. On the flip side, I'm wondering what could have gone wrong with my setup in six months. 'Cause six months is too short for this problem, right?
I have some Hifiman headphones (HE-X4) that no longer work on one side. Is it possible to order a replacement side (if it is self servicable) or send them in for repair?
Hello,
after long waiting i got this new pcb and went to configure it. So after doing so running mdloader it goes 60sec countdown and when i press FN+B just types .....bbbbb.bbb.b. etc. So it looks like on my pcb doesnt have the b button configured (becuase it types b instead dfu) to go to dfu mode hence i cant flash the pcb. Any other way to flash the board please? It should be on b by default as it seems...so i dont know what is the problem here.
thanks
Hello! I'm looking to find a set of MT3 alpha keycaps that match the color of the white "alpha" keys in the LotR Elvish MT3 set. The Mito MT3 Godspeed R2 set looks close, but it's hard to tell from the photos. Has anyone replaced the alpha keys on their Elvish set with roman alphabet keycaps? Thanks in advance!
Is anyone's DROP High-Profile CTRL keyboard randomly disconnecting?
With LEDs on, this keyboard will randomly disconnect in the middle of typing or during a game. I've tried:
Using the cable they gave me(always have been)
Plugging it into different USB ports on my computer
Turning off the LEDs (that's how I diagnosed it, per support as well)
Even returned it in exchange for another, and it's still happening.
The top three bullets are what support told me to test, and I did just that. It's no issue if the LEDs are off, but I want them on. Can anyone else with the new CTRL High-profile keyboards fill in on whether or not they are experiencing this? It's happening much more frequently. I'm not sure if it's because of my motherboard being slightly older and not supply enough power, or a keyboard issue.
As the title states, i never made an account with drop and was made one after purchasing something here. It's asking me to provide my old password (which i don't have, never made one) to create a new one. usually websites would provide a "Forgot Password" option to recover or change your password but this doesn't. Anyone know whats going on?
I recently purchased EPOS PC38X to use with my Nintendo switch. I have it plugged in and sounds great. But I can't get the mic to work. Any suggestions?
Thank you
How long does it take for Drop orders to start shipping?(regular in stock item)
Based in EU west. Not talking about the time it takes to arrive once it has been sent off, but the time it takes between payment and shipping.
I’ve ordered a set of Mt3 keycaps and I’ve heard a lot of horror stories about drop processing times.
I want to give my wife a Winnie the Pooh keyboard using Drop's base and novelties kits.
I don't know what keyboard to get with it. I want silent keys and smooth, linear action. She is accustomed to Mac keyboards.
Finally, she uses the number pad so I either need a full-sized keyboard (preferred) or I could get a separate keypad. I've looked at the Drop Shift V2, but there seems to be a bit of discontent with this board, so perhaps there is something better.
So, would anyone care to share a recommended keyboard, switches, whatever I need to make this work?
Thanks in advance.
Where can I get the rubber feet of Drop Ctrl keyboard (on the back)?
Sorry, not sure if that's the right name for the part. It bothers me a long time, just want to see how I can replace the rubber feet on the back of the Drop Ctrl keyboard when now all of them are dropped ...
Thanks so much.
Where to find Fn key on Drop CTRL V2 Mechanical Keyboard PCBA
This is probably a really basic question and I thank you in advance for an answer. I just got the CTRL V2 and used the configurator to make a few changes. To flash the firmware I need to use the Fn key, which is not showing up anywhere on the key mapping in the configurator. In fact, the Fn key is repeatedly referenced in the "Basic" functions of the configurator, but I have no idea where it is. I have gone round and round with DROP Support and they keep pointing me to the configurator, which is no help; it does not list the location of the Fn key. Again, thanks for your help!
Hey everyone!!
I am 15 and I would like to buy a budget earbud for Christmas
I have come to a conclusion between the Final E2000
and the Sony XBA-10 which one do you recommend for me
I listen to hip hop and rap mostly.
I am now just concerned of the bass on the Sony XBA-10.
The wires on the left channel plug, just before the socket are acting up and I need to replace the cable for my Sennheiser 6XX headphones.
Looking at Amazon, I see actual Sennheiser cables but one of them does not have the removable 1/4 plug (I use a DAC with 1/8" jack), and I would rather not add even more connection unknowns by using an adapter down to 1/4", and the other Sennheiser cable is far too long for my usage (looking for around 2 meters or just a touch longer.
The 6XX have been around for a while and I'm sure I'm not the first to need a replacement cable. I'm actually surprised that Drop doesn't offer them perpetually like they do with the ear pads, which ironically my stock pads are holding up just fine.
I'm not looking for $100+ cables here, just a solid replacement for what the 6XX came with.
Thanks!
Massdrop Ctrl rgb setting doesn't save after computer is turned off.
Whenever I turn my computer on from being shut off, the rgb setting always resets. It only saves the rgb setting if the computer is restarted. Would anyone know the solution to this problem?
Thank you.
Drop CTRL High profile acrylic diffuser replacement
Does anyone able to replace the current acrylic diffuser to a brass or any kind of plate? If yes, can I know where you bought it and some pictures if you may is very much appreciated :)
If none, do DROP even consider creating one? I'll buy in a heartbeat.
Thanks!
About
Photos, insights, discussions, you name it: Consider this home base for all your interests. Take a look around and discover more about what you love.